Agio-international Multi-Purpose Work Bench 92558 Manuale Utente Scaricare il pdf

QTY

DESCRIPTION ORDER PART #

QTY

DESCRIPTION ORDER PART #

QTY

DESCRIPTION ORDER PART #

M10 X 55MM BOLT

M6 X 50MM BOLT

M6 X 16MM BOLT

M6 NUT

6MM WASHER

10MM WASHER

12MM WASHER

10MM END CLIP

12MM END CLIP

10MM PVC COVER

12MM PVC COVER

M6 PVC NUT COVER

LARGE WHEEL

WHEEL COVER

AXLE SLEEVE

RIGHT SUPPORT

FRAME

LEFT SUPPORT

FRAME

CUSHION

HANDLE GRIP

CASTERS

FRONT SUPPORT

BAR

REAR SUPPORT

BAR

MIDDLE SUPPORT

FRAME

FRONT PANEL

COILED SHELF

DRAIN PLUG

DOWEL RODS

REAR FAUCET

PANEL

FOLDING

COUNTER

AXLE FOR

FOLDING COUNTER

DRAWER

BOTTOM TRAY

“S” HOOKS

FAUCET

FOLDING COUNTER

HINGE

STEP 1

identify all parts packed in carton against the parts list. Remove all protective materials. Place parts

on a non-arasive surface to avoid scratching. If you are missing any parts or are unsure how to

proceed with assembly, call our Customer Service Center at 1-800-416-3511 (Mon - Fri 9a-5p

EST). Do not attempt assembly if any parts are missing or damaged.

Read entire assembly instructions before beginning assembly.

I I

WHEEL AXLE

SINK TOP BASIN

STEP 2 WHEEL ASSEMBLY

Insert wheel axle (M) through bottom shaft of right side support frame

(Q).so that it is centered inside the shaft with equal amount of axle on

each side. Snap 12mm end clip (I) on notch in axle closest to the right

side support frame (Q). Add the following parts to the axle in this order:

12mm washer (G), wheel cover (O), axle sleeve (P), wheel (N), wheel

cover (O), 12mm washer (Q), 12mm end clip (I) as shown in figure 1. Be

sure the wheel is inserted over the axle sleeve in a manner that allows it

to rotate freely. Secure the wheel assembly on the axle with the 12mm

washer clip (I). Repeat procedure for opposite side wheel.

STEP 3 LEFT SIDE SUPPORT FRAME ASSEMBLY

Screw in the two casters (T) into the bottom of the left side support frame (R) as

shown in figure 2. Add the cushion handle grip (S) to the left side support frame

(R) as shown in figure 2. Insert two M6 x 50mm bolts (B) through end of cushion

grip handle and through the holes in the left side support frame. Add a 6mm

washer (E), 6mm nut (D). Tighten with wrench. Do not over tighten. Add M6 PVC

cover to the end of each nut. Repeat on opposite side of cushion grip handle.

Figure 1

Figure 2

WB0001 WB0014

WB0013

WB0012

WB0011

WB0010

WB0009

WB0008

WB0007

WB0006

WB0005

WB0004

WB0003

WB0002

WB0023

WB0022

WB0021

WB0020

WB0019

WB0018

WB0017

WB0016

WB0015

WB0024

PAGE 1

TOOLS REQUIRED FOR ASSEMBLY

Hex Wrench

Hex Bolt Driver

MULTI-PURPOSE WORK BENCH ASSEMBLY INSTRUCTIONS

#92558

1 2 3 4

Sommario

Pagina 1 - Figure 2

QTYDESCRIPTION ORDER PART #QTYDESCRIPTION ORDER PART #QTYDESCRIPTION ORDER PART #M10 X 55MM BOLT3M6 X 50MM BOLT6M6 X 16MM BOLT16M6 NUT126MM WASHER610M

Pagina 2 - Figure 5

STEP 4 FRAME ASSEMBLYConnect right side support frame (Q) and left side support frame (R) using the rear support bar (V). Be sure that the hole in th

Pagina 3 - Figure 7

STEP 6 SINK ASSEMBLY (continued)Position the sink top assembly (Z) over the left side, right side and middle support frames, making sure the holes fo

Pagina 4 - Figure 8

STEP 8 FINAL TOUCHESDrawer assembly. Tilt the front end of drawer up and slide into track. Make sure track and drawer runners are properly aligned.

Commenti su questo manuale

Nessun commento

Agio-international Multi-Purpose Work Bench 92558 Manuale Utente

Navigare online o scaricare Manuale Utente per Mobilio Agio-international Multi-Purpose Work Bench 92558. Agio International Multi-Purpose Work Bench 92558 User Manual Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Mobilio Agio-international Multi-Purpose Work Bench 92558